Microstructure and electromagnetic properties of LiFe5O8 ferrite ceramics prepared from wet- and dry-milled powders

The effect of dry and wet ball milling of LiFe₅O₈ ferrite powder on the microstructure and electromagnetic properties of ferrite ceramics was studied using XRD analysis, scanning electron microscopy, dilatometry, thermogravimetry, calorimetry, and measurement of specific magnetization and electrical resistance. The sintering temperature was 1050 °C; the sintering time was 2 h. It was found that ferrite fabricated from dry-milled powder exhibits an ordered α-LiFe₅O₈ phase with bulk density of 91%. Its saturation magnetization and Curie temperature are 55 emu/g and 628°С, respectively. Specific electrical resistance is 4?10⁶ Ω cm. Wet milling in isopropyl alcohol causes formation of a disordered β-LiFe₅O₈ phase. Ceramics produced by this method shows higher bulk density (97%) and low porosity, and an order of magnitude lower resistivity. Its saturation magnetization and Curie temperature are 51 emu/g and 607°С, respectively.     

Low/intermediate temperature pyrolyzed polysiloxane derived ceramics with increased carbon for electrical applications

This study focuses on the chemistry, thermal stability, and electrical conductivity of low/intermediate pyrolysis temperature (700?900 °C) polysiloxane derived ceramics. These ceramics were modified with additional carbon derived from divinylbenzene (DVB) added to the precursor. Their electrical properties were investigated for potential uses in micro-electrical mechanical systems (MEMS) and anodes for lithium batteries. The microstructure and chemical composition was investigated by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), Raman spectroscopy, and x-ray photoelectron spectroscopy (XPS); thermogravimetric analysis (TGA) provided insight into the thermal stability; and electrochemical impedance spectroscopy (EIS) into the electrical properties of the material. The increase of pyrolysis temperature and carbon content lead to an enhancement of the electrical conductivity, higher than previously reported values for intermediate pyrolysis temperature SiOC polymer derived ceramics. A limit of the amount of DVB that can be added to PHMS to produce a hybrid precursor has also been obtained.     

Influence of nucleating agents on crystallization and electrical properties of SiO2–MgO–MgF2–K2O mica glass-ceramics

The effects of adding ZrO₂ and TiO₂ at the expense of MgF₂ on the crystallization, microstructure, mechanical properties, thermal properties and electrical properties of mica glass-ceramics based on the SiO₂–MgO–MgF₂–K₂O system were investigated by the differential scanning calorimetry (DSC), X-ray powder diffraction (XRD), scanning electron microscopy (SEM), microhardness tester and resistivity tester. The electrical properties were discussed emphatically. The results showed that the additions of ZrO₂ and/or TiO₂ at the expense of MgF₂ effectively increase the viscosity, the glass transition temperatures (T_g) and the crystallization temperatures (T_p) of the glasses. The crystallization activation energy (E_c) of the amorphous glasses varied with the nucleating agents was discussed in depth. It was discovered that the nucleating agents had no effect on the crystal phase type but had a certain effect on the crystallinity and microstructure. Tetrasilicic fluoromica and enstatite were precipitated at different crystallization temperatures. Due to the non-stoichiometric ratio of tetrasilicic fluoromica crystal, the prepared glass-ceramics had high dielectric constant (24.4–34.3) and volume resistivity (>2 × 10¹¹ Ω cm) at 25 ^°C, and the dielectric loss was almost zero.     

Influence of Se and Te substitutions at Tl-site of Tl(Ba,Sr)CaCu2O7 superconductor on the AC susceptibility and electrical properties

The Sr and Ba bearing Tl-1212 phase, Tl(Ba,Sr)CaCu₂O₇ is an interesting superconductor. The Sr only bearing TlSr₂CaCu₂O₇ is not easily prepared in the superconducting form. The Ba only bearing TlBa₂CaCu₂O₇ on the other hand does not show improvement in the transition temperature with elemental substitution. In this work the influence of multivalent Se (non-metal) and Te (metalloid) substitutions at the Tl-site of Tl_1-xM_x(Ba,Sr)CaCu₂O₇ (M = Se or Te) superconductors for x = 0–0.6 was studied. The samples were prepared via the conventional solid-state reaction method. XRD patterns showed a single Tl-1212 phase for x = 0 and 0.1 Se substituted samples. The critical current density at the peak temperature, T_p of the imaginary (χ”) part of the AC susceptibility (χ = χ’ +χ”), J_c-inter(T_p) for all samples was between 15 and 21 A cm⁻². The highest superconducting transition temperature was shown by the x = 0.3 Se-substituted sample (T_c-onset = 104 K, T_c-zero = 89 K, T_cχ’ = 104 K and T_p = 80 K). Te suppressed the superconductivity of Tl-1212 phase. The order of highest transition temperatures are as follows: Tl_1-xTe_x(Ba,Sr)CaCu₂O₇<Tl(Ba,Sr)CaCu₂O₇<Tl_1-xSe_x(Ba,Sr)CaCu₂O₇. This work showed that Se was better than Te in improving the transition temperature and flux pinning of the Tl-1212 phase. The roles of ionic radius of Se and Te on the superconductivity of Tl(Ba,Sr)CaCu₂O₇ are discussed in this paper.     

Effects of (Li0.5Sm0.5)/W co-substitution and sintering temperature on the structure and electrical properties of ultrahigh Curie temperature piezoceramics,Ca0.92(Li0.5Sm0.5)0.08Bi2Nb2-xWxO9

With co-substitution of (Li_0.5Sm_0.5) at A site and W at B site, the electrical properties of modified Ca_0.92(Li_0.5Sm_0.5)_0.08Bi₂Nb_2-xW_xO₉ [(CLS)BN-xW, x = 0, 0.015 and 0.03] piezoceramics with ultrahigh Curie temperature (T_C) of > 930 °C were enhanced dramatically. The increased resistivity induced by the co-substitution ensure them to be polarized under an enough high field. Combined with the increase of spontaneous ferroelectric polarization (P_S), the significant enhancements in the piezoelectric, dielectric and ferroelectric properties can be obtained in the composition x = 0.015. Furthermore, the piezoelectric activity (d₃₃) and bulk resistivity (ρ_b) of (CLS)BN-0.015 W can be further enhanced at an appropriate sintering temperature. This optimum composition sintered at 1170 °C shows ultrahigh T_C of ～948 °C, d₃₃ of ～17.3 pC/N and ρ_b of ～6.9 MΩ cm at 600 °C, which are comparable to those of the reported high-temperature Aurivillius piezoceramics with T_C > 850 °C.     

Preparation and properties of AZO/PS/AZO tri-layer transparent conductive film with a light-trapping structure

The light-trapping structure is an effective method to increase solar light capture efficiency in the solar cells. In this study, Al-doped ZnO (AZO)/polystyrene (PS)/AZO tri-layer transparent conductive film with light-trapping structure was fabricated by magnetron sputtering and liquid phase methods. The structural, optical and electrical properties of the AZO films could be controlled by different growth conditions. When the sputtering pressure of the under-layer AZO film was 0.2 Pa, the discharge voltage was around 80 V, which was within the optimal process window for obtaining AZO film with high crystallinity. The optimal under-layer AZO film had a large surface roughness and a very low static water contact angle of 75.71°, promoting the relatively uniform distribution of PS spheres. Under this sputtering condition, the prepared AZO/PS/AZO tri-layer film had the highest crystallinity and least point defects. The highest carrier concentration and Hall mobility are 3.0 × 10²¹ cm^-3and 5.39 cm² V^-1 s^-1, respectively. Additionally, a transparent conductive film with the lowest resistivity value (3.88 × 10^-4 Ω cm) and the highest average haze value (26.5%) was obtained by optimizing the process parameters. These properties were comparable to or exceed the reported values of surface-textured SnO₂-based as well as ZnO-based TCOs films, making our films suitable for transparent electrode applications, especially in thin-film solar cells.     

Structural,optical, and electrical properties of tin iodide-based vacancy-ordered-double perovskites synthesized via mechanochemical reaction

Over the recent past, lead-based halide perovskite materials have drawn significant attention due to their excellent optical and electrical properties for solar cells and optoelectronics applications. However, the toxicity of lead elements and instability under ambient conditions leads to develop alternative compositions. Herein, we report a novel mechanochemical synthesis of tin iodide-based double perovskites (A₂SnI₆; A = Rb⁺, Cs⁺, methylammonium, and formamidinium), and their structural, optical, and electrical properties are investigated. Importantly, we found that the hydrogen iodide (HI) addition during the ball-milling process minimizes secondary phase formation in the synthesized A₂SnI₆ powders. The effects of HI addition and the A-site substitution are investigated with respect to the lattice parameters, optical bandgaps, and electrical properties of the synthesized perovskite materials. Our results demonstrate essential information to improve the understanding of halide perovskite materials and develop efficient lead-free perovskite photoelectric devices.     

三维石墨烯-碳纳米管/水泥净浆的压敏性能

为了探索三维石墨烯-碳纳米管(G-CNTs)/水泥净浆的压敏性能,采用四电极法研究了荷载作用下GCNTs/水泥净浆的电阻率变化,并分析不同G-CNTs掺量、加载幅度、加载速度以及恒定荷载对电阻率变化的影响。研究表明:随着G-CNTs掺量的增加,电阻率呈先减小后稳定的变化趋势,在G-CNTs掺量由0.2wt%增加至1.6wt%时,电阻率下降51.8%;电阻率与温度呈负相关;G-CNTs掺量高于0.8wt%时可以显著提高水泥净浆的压敏性能,且电阻率变化率与应力应变有明显的对应关系,1.2wt%G-CNTs掺量下试件的应力灵敏系数和应变灵敏系数分别为2.3%/MPa和291;G-CNTs/水泥净浆电阻率变化率幅值随着加载幅度增大而相应增加,其电阻率变化率曲线在不同加载速度以及恒定荷载作用下均与应力-应变曲线一一对应,具有良好的压敏特性。     

Influence of Al3+ doping for V5+ on the structural,optical, thermal and electrical properties of V2-xAlxO5-δ (x=0–0.20) ceramics

This paper reports an investigation on the structure-properties correlation of trivalent metal oxide (Al₂O₃)-doped V₂O₅ ceramics synthesized by the melt-quench technique. XRD patterns confirmed a single orthorhombic V₂O₅ phase formation with increasing strain on the doping of Al₂O₃ in place of V₂O₅ in the samples estimated by Williamson-Hall analysis. FTIR and Raman investigations revealed a structural change as [VO₅] polyhedra converts into [VO₄] polyhedra on the doping of Al₂O₃ into V₂O₅. The optical band gap was found in a wide semiconductor range as confirmed by UV–visible spectroscopy analysis. The thermal and conductivity behavior of the prepared samples were studied using thermal gravimetric analysis (TGA) and impedance analyzer, respectively. All the prepared ceramics exhibit good DC conductivity (0.22–0.36 Sm^-1) at 400 ?C. These materials can be considered for intermediate temperature solid oxide fuel cell (IT-SOFC)/battery applications due to their good conductivity and good thermal stability.